Short answer: Choose a bandsaw whose capacity is at least 10 to 20% larger than the biggest section you cut today, measured in the shape you actually cut (round, square or rectangular). If you mitre, check the capacity at your angle, not at 90°. Then confirm bar length, workshop space and power supply.
Start with your largest section, not your average one
A bandsaw is sized by the biggest piece it can clamp and cut. List the largest round bar, square bar, flat and beam you cut now, plus anything you expect to quote for in the next few years. Size to that list with 10 to 20% headroom.
Headroom matters because a saw working at the edge of its capacity runs slower, wears guides faster and leaves no margin for a bent or oversized bar. It also stops you turning work away when a customer sends a larger section.
Read the capacity chart properly
Every bandsaw lists several capacities, and they are not interchangeable.
Round: the largest diameter bar that fits between the vice jaws and under the blade.
Square: the largest square section. This is usually smaller than the round figure.
Rectangular: width × height. A saw rated 360mm × 250mm will not cut a 300mm square.
Bundle: the maximum stack height and width if you cut several bars at once.
On our Alligator bandsaws the model number tells you the headline figure. On manual and semi-automatic (SAF) machines it is the jaw capacity. On CNC machines it is the round capacity, with the jaw opening slightly larger.
Check the mitre capacity
Capacity drops as the head swivels. A saw that cuts 300mm at 90° can lose a quarter or more of that capacity at 45° and far more at 60°, so always check the mitre figures on the spec sheet. If you cut mitred steel sections for fabrication, size to your largest mitred cut and look for a pivot mitring machine that swivels in both directions.
Blade width follows machine size
Larger machines run wider, thicker blades that stay straight through deep cuts. As a guide:
|
Machine capacity |
Typical blade width |
Typical blade thickness |
|
Up to 250mm |
27mm |
0.9mm |
|
250 to 400mm |
34mm |
1.1mm |
|
400 to 600mm |
41mm |
1.3mm |
|
600 to 800mm |
54mm |
1.6mm |
|
Over 800mm |
67mm or 80mm |
1.6mm |
A wider blade cuts straighter and lasts longer in solids, and the price per band is not always much higher. That is part of the reason an undersized saw costs more to run.
Bar length, feed and floor space
Think about the length of stock you receive. Six metre bars need infeed and outfeed support, so plan space for roller tables either side of the saw.
On automatic bandsaws check the single feed stroke length. A 500mm stroke cuts a 1,200mm part in three strokes, which is slower than one long stroke.
Most industrial bandsaws run on 400V three phase. Confirm your supply before ordering, along with access to get the machine into position.
Quick sizing checklist
Largest round, square and rectangular section you cut
Largest mitred cut and the angle
Bundle cutting needed or not
Stock length and roller table space
Cuts per day (this decides manual, semi-automatic or automatic)
Power supply and floor space
FAQs
Can I cut a bar larger than the stated capacity? No. A bar may fit in the vice but still foul the bow or the blade guides as the head comes down. Forcing an oversized bar risks the blade, the machine and the operator. Size up instead.
Is a bigger bandsaw always better? Not always. A very large saw is slower on small sections and uses more expensive blades. Size to your work with sensible headroom.
Do I need a horizontal or vertical bandsaw? Horizontal bandsaws cut bar and section to length. Vertical bandsaws suit plate, contour cutting and awkward shapes.
Talk to us
Send us your largest sections and daily cut volume and we will recommend the right size from our Alligator range and partner brands. Call 01892 663398, contact us online or book a test cut at our Crowborough showroom.
Share this post: